View GP2A200LCS0F_1078038.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GP2A200LCS0F Series
GP2A200LCS0F Series
Detecting Distance : 2 to 22mm *OPIC Output, Reflective Photointerrupter with Connector
Description
GP2A200LCS0F Series are OPIC output, reflective photointerrupters with emitter and detector facing the same direction in a molding that provides non-contact sensing. This family of devices uses light modulation to reduce the affects of disturbing light, and the sensor is optimized to work in the selected focal distance. A 3-pin connector is included to allow remote-mount or off-board designs.
Agency approvals/Compliance
1. Compliant with RoHS directive
Applications
1. General purpose detection of paper presence or motion. 2. Example: PPC, FAX, Printer
Features
1. Reflective with OPIC Light Modulated Output 2. Highlights : * Includes additional screw fixing holes * Position pin to prevent mis-alignment * Long focal distance 3. Key Parameters : * Detecting distance : 2 to 22mm (White paper) 5 to 15mm (Black paper) * Undetecting distance : over 90mm (White paper) * Connector : GP2A200LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A200LCSCF ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A240LCS0F ; Tyco Electronics AMP K.K. (PN : 292133-3) GP2A210LCSJF ; Tyco Electronics AMP K.K. (PN : 4-292133-3) 4. Lead free and RoHS directive compliant
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signalprocessing
Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: D3-A05101EN Date Jun. 30. 2005 (c) SHARP Corporation
GP2A200LCS0F Series
Internal Connection Diagram
Reflective object Voltage regulator Demodulator circuit
1 1 2 3
2
VCC VOUT GND
Amp.
3
Comparator
Oscillator circuit
Sync. detecting circuit
Outline Dimensions
GP2A200LCS0F
33 3.1 4.5 9 17.7 (7.8) 9.6 7 (6.8)
(Unit : mm) GP2A200LCSCF
3.5 3.2 6.1 3.5 5.2 (5.8) 7.8
1 2 3
View A
3.
6.2
6 12
Optical center VCC VOUT GND 9
2
Connector : 292133-3 (Tyco Electronics AMP K.K.) 6 12
3
(5.8)
1 2 3
Connector : 292133-3 (Tyco Electronics AMP. K. K) 8 4.5
5.2
VCC VOUT GND
+0 3-0.2
(0.65)
2.5
10.2 (0.9)
7
3.5
0
* Unspecified tolerance shall be as follows ;
26.5 32 4-SR1 View A
0 2
(6.8) (7.8)
* Unspecified tolerance shall be as follows ;
Date code
Dimensions Tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4
* *( ) : Reference dimensions
Date code
Dimensions Tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4
* *( ) : Reference dimensions
Product mass : approx. 1.95g GP2A210LCSJF
33 3.1 4.5 9 17.7 (6.8)
Product mass : approx. 2.3g GP2A240LCS0F
33 3.1 4.5 17.7 (7.8) (6.8)
(7.8)
9
1 2 3
3.2
6.2
6 12
Optical center
VCC VOUT GND
1 2 3
3.2
6.2
6 12
Optical center
Connector : 4-292133-3 (Yellow) (Tyco Electronics AMP K.K.) 8 4.5 (5 .8)
7.8 8 4.5
Connector : 292133-3 (Tyco Electronics AMP K.K.) (0.65) (5 .8)
7.8
2.5
2.5
26.5
3+0.0 -0.2
123
26.5
2
123
9
9
* Unspecified tolerance shall be as follows ;
5
1
* Unspecified tolerance shall be as follows ;
Date code
*
: Portion Built-in IR-90 filter
Dimensions Tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4
* *( ) : Reference dimensions
Date code
Dimensions Tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4
* *( ) : Reference dimensions
Product mass : approx. 1.95g
Product mass : approx. 1.95g
Connector terminal plating material : Sn
Sheet No.: D3-A05101EN
2
2
3+0.0 -0.2
2 VCC VOUT GND
26.5
123
2
4.5
Optical center
3+0.0 -0.2 2
7.8
2 1
GP2A200LCS0F Series
Date code (2 digit)
1st digit Year of production A.D. Mark 2000 0 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0 : : 2nd digit Month of production Month Mark 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 X 11 Y 12 Z
repeats in a 10 year cycle
Country of origin
Japan
Sheet No.: D3-A05101EN
3
GP2A200LCS0F Series
Absolute Maximum Ratings
Parameter Supply voltage Output voltage *1 Output current *2 Operating temperature *2 Storage temperature

Symbol VCC VO IOL Topr Tstg
Rating -0.5 to +7 30 50 -10 to +70 -20 to +80
(Ta=25C) Unit V V mA C C
1 Sink current refer to Fig.5. 2 The connector should be plugged in/out at normal temperature.
Electro-optical Characteristics
Parameter Supply voltage Current dissipation (I) *3 Current dissipation (II) Low level output voltage High level output voltage *4 Non detection distance GP2A210LCSJF
*4
Symbol VCC ICC ICCP VOL VOH LLHL LHLS
Condhitions - Smoothing value VCC=5V, RL= Pulse peak value VCC=5V VCC=5V, IOL=16mA, at detecting time VCC=5V, RL=1k, at non detecting time KODAK Gray Cards, VCC=5V KODAK Gray Cards, VCC=5V Black paper, VCC=5V KODAK Gray Cards , VCC=5V Black paper, VCC=5V VCC=5V -
Detection distance LHLL
*5
Response time Acceptable illuminance
*6
tPLH tPHL Ev1 Ev2
MIN. 4.75 - - - 4.5 - - - - 22 15 - - 3 000 1 500
TYP. - - - - - - - - - - - - - - -
MAX. 5.25 30 150 0.4 - 90 70 2 5 - - 1 1 - -
(Ta=25C) Unit V mA mA V V mm mm mm ms ms lx lx

3 Refer to Fig.1. 4 Refer to Fig.2. 5 Refer to Fig.3. * 6 Refer to Fig.4.
Reflective object
Black paper (black) : Standard reflective object (provided by SHARP Corporation) KODAK Gray Cards (use the white side reflects about 90%) : Standard reflective object (provided by SHARP Corporation) PPC paper : Standard reflective object (provided by SHARP Corporation)
Sheet No.: D3-A05101EN
4
GP2A200LCS0F Series
Fig.1 Test Condition for Peak Pulse Value ICCP
R=1
1 2 3
V
RL=1k VO GND tW tP ICCP=Vr/1 tW (TYP.)=8s (GP2A240LCS0F : 2.5 to 9.3s) tP (TYP.)=130s (GP2A240LCS0F : 40 to 150s)
Photointerrupter
Fig.2 Test Condition for Detecting Distance Characteristics
Output VO Reflective object VOH
VOL Detecting distance L LHLS LHLL LLHS LLHL
Detection surface
Fig.3 Test Circuit for Response Time
Reflective object Detection surface
1 2 3
With reflective object RL=1k VCC=5V VO GND VOUT waveform tPHL tPLH VOH 1.5V VOL Without reflective object
L
Photointerrupter
Fig.4 Test Condition for External Disturbing Light Illuminance
EV1 : At non-detecting Emission/detection surface Light source A Photointerrupter Illuminance shall be that on the emission/detection surface. Output shall not go from "H" to "L". Light source A EV2 : At detecting PPC paper Emission/detection surface Photointerrupter Illuminance shall be that on the reflective object. Output shall not go from "L" to "H". 15mm
Vr
VCC=5V
Sheet No.: D3-A05101EN
5
GP2A200LCS0F Series
Fig.5 Output Current vs. Ambient Temperature
50
Fig.6 Low Level Output Voltage vs. Ambient Temperature
0.3 VCC=5V At detecting IOL=30mA 0.2 16mA
40
30
20
Low level output voltage VOL (V)
Output Current IOL (mA)
0.1 5mA
10 0 -10
0
25
50
70 75
100
0 -10
0
10
20
30
40
50
60
70
Ambient temperature Ta (C)
Ambient temperature Ta (C)
Fig.7 Low Level Output Voltage vs. Low Level Output Current
VCC=5V At detecting Low level output voltage VOL (V)
Fig.8 Dissipation Current(Smoothing Value) vs. Ambient Temperature
7 Ta=-10C 6 Dissipation current ICC (mA) 5 4 3 2 1 25C 70C
0.1
0.01
1
10 Low level output current IOL (mA)
100
0 4.75
4.85
4.95
5.05
5.15
5.25
Supply voltage VCC (V)
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
Sheet No.: D3-A05101EN
6
GP2A200LCS0F Series
Design Considerations Design guide
1) VO terminal : Open collector output This product operates the light emitter by pulse drive. Please supply the stable supply voltage in order to prevent error operation by pulse current. Please use this device after connecting a capacitor between VO and GND for prevention of line noise. 2) Prevention of detection error Please be careful that you need to keep the direct inverter light away from the photo detecting surface since the device will not operate correctly in such case. In addition, we recommend to make sure the operation test in the actual application. 3) Plugging in/out The connector should be plugged in/out at normal temperature. This product is not designed against irradiation and incorporates non-coherent IRED.
Parts
This product is assembled using the below parts.
* Photodetector (Q'ty : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit]
Category Phototransistor Maximum Sensitivity wavelength (nm) 900 Sensitivity wavelength (nm) 700 to 1 200 Response time (s) 400
* Photo emitter (Q'ty : 1)
Category Infrared emitting diode (non-coherent) Material Gallium arsenide (GaAs) Maximum light emitting wavelength (nm) 950 I/O Frequency (MHz) 0.3
* Material
Case GP2A200LCS0F GP2A200LCSCF GP2A210LCSJF GP2A240LCS0F Black polyphernylene Sulfide resin (UL94 V-0) Polycarbonate resin (UL94 V-2) Polycarbonate resin (Gray) (UL94 V-2) Polycarbonate resin (Navy Blue) (UL94 V-2) Lens Bottom cover
The IR-90 filter (Fuji Photo Film Co., Ltd.) is inserted between case and detector side lens.
* Others
Laser generator is not used.
Sheet No.: D3-A05101EN
7
GP2A200LCS0F Series
Manufacturing Guidelines Cleaning instructions
Polycarbonate resin is used as the material of the lens surface. So this product shall not be cleaned by cleaning solvent absolutely. Dust and stain shall clean by air blow, or shall clean by soft cloth.
Presence of ODC
This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). *Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE).
Sheet No.: D3-A05101EN
8
GP2A200LCS0F Series
Package specification Case package Package materials
Anti-static plastic bag : Polyethtylene Moltopren : Urethane Packing case : Corrugated fiberboard
Package method
100 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the packing case is covered with moltopren, and 2 plastic bags shall be put int the packing case. Moltopren should be located after all product are settled (1 packing conteains 200 pcs).
Packing composition
Moltopren
plastic bag
Packing case
Sheet No.: D3-A05101EN
9
GP2A200LCS0F Series
Important Notices
* The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. * Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. * Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). * If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. * This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. * Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
[H176]
Sheet No.: D3-A05101EN
10

▲Up To Search▲

Price & Availability of GP2A200LCS0F

	To Download GP2A200LCS0F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .